Troy-bilt 13045 User Manual

PRINTED IN U.S.A.Operator’s ManualIMPORTANT: READ SAFETY RULES AND INSTRUCTIONS CAREFULLYWARNING: This unit is equipped with an internal combustion e

10• Push the cable coupler through the end of the spring to expose the lock nut. See Figure 9. Figure 9• Thread the lock nut outward (down the coupler

11• Move the shift lever into the fast reverse (R2) position and repeat the previous two steps. If you experienced resistance rolling the unit, either

12Tire Pressure (Pneumatic Tires)The tires are overinflated for shipping purposes. • Check the tire pressure before operating the snow thrower. Refer

13LubricationAuger Shaft• At least once a season, remove the shear bolts from the auger shaft and spray lubricant inside the shaft. See Figure 13.• Gr

14Check Friction Wheel RubberFollow the instructions below to check the condition of the friction wheel rubber every 25 hours of operation.• Remove th

15Figure 17• Pull the brake bracket assembly towards the cable guide roller and unhook the auger cable “Z” fitting.• Remove the upper bolts and lock w

16• Reassemble the two halves of the unit hooking the lower portion of the auger housing over the stationary shoulder bolts in the frame assembly.Figu

17• Insert the hex shaft through the sprocket and the spacer. Make certain that the chain engages both the large and the small sprocket.NOTE: If the s

182429302039132455576825254042818315725432713171391425263434263214142121161023121335113725132219133325144128153638444546471425495250535455565148585960

19Model 13045Ref. No.Part No. Part Description1. 05244A Bearing Housing2. 618-0281A Bracket Assembly, Auger Break3. 684-0090A Impeller Assembly, 16”4.

2TABLE OF CONTENTSContent PageImportant Safe Operation Practices ... 3Loose Parts

20Model 1304518127617816911454966435353645451018182473324253923346714512775716458222129135652372223313291819474961481562275166423633347306511656471949

21Model 13045Ref. No.Part No. Part Description1. 05523 Pivot Support Bracket2. 750-1302A Spacer, .6725 x 1.125 x 2.4853. 618-0279 Dogg Assembly LH4. 6

22Model 1304511234545191919196677991021132911222431172723152621151425161822112015283015231321333232AAAA3334343535363738394042434481243

23Model 13045Ref. No.Part No. Part Description1. 646-0012 Cable Assembly, Auger/Drive2. 684-0053B Chute Crank Assembly, Lower3. 705-5266 Chute Crank B

24Model 13045Ref. No.Part No. Description1. 07386 Washer2. 684-0123A Belt Cover Bracket Assembly3. 710-0191 Hex Screw 3/8-24 x 1.25”4. 710-0237 Hex Sc

25Model 13045Ref. No.Part No. Description1. 710-0276 Carriage Screw2. 710-0458 Carriage Bolt 5/16-18 x 1.75”3. 710-0805 Hex Bolt 5/16-18 x 1.5”4. 710-

26Model 13045NOTE: When rebuilding a gearbox assembly, include 3 oz. of Shell Alvania EP Lead-Free Grease (Part No. 737-0168).Ref. No.Part No. Descrip

27Model 13045

MANUFACTURER’S LIMITED WARRANTY FOR:The limited warranty set forth below is given by Troy-Bilt LLC with respect to new merchandise purchased and used

3SECTION 1: IMPORTANT SAFE OPERATION PRACTICESThis symbol points out important safety instructions, which if not followed, could endanger the persona

44. Never operate with a missing or damaged discharge chute. Keep all safety devices in place and working.5. Never run an engine indoors or in a poorl

5SECTION 2: ASSEMBLING YOUR SNOW THROWERNOTE: All references to right or left side of the snowthrower are determined from behind the unit in theopera

6Attaching Chute Directional Control• Remove the hairpin clip from the upper rod and slide the upper rod through the bracket and into the lower rod. S

7Figure 7Safety Ignition KeyThe ignition key must be inserted in the switch in order for the engine to start. Remove the ignition key when the snow th

8Chute Clean-out ToolWARNING: Never use your hand to clear aclogged discharge chute. Shut off engine andremain behind handles until all moving partsha

9• When engine starts, release starter button, and move choke gradually to OFF. If engine falters, move choke immediately to FULL and then gradually t