Troy-bilt 1028 User Manual

SNOW THROWERMODELS10281130Storm TrackerOperator’s ManualPRINTED IN U.S.A.IMPORTANT: READ SAFETY RULES AND INSTRUCTIONS CAREFULLYWARNING: This unit is

10• Confirm that the auger has completely stopped rotating and shows NO signs of motion. IMPORTANT:If the auger shows ANY signs of rotating, immediate

11SECTION 5: MAKING ADJUSTMENTSWARNING: NEVER attempt to make anyadjustments while the engine is running,except where specified in the operator’smanu

12Shift Rod AdjustmentTo adjust the shift rod, proceed as follows:• Remove the hairpin clip and slide the shift rod connector up, to separate the uppe

13Drive / Auger Control LockThe cams on the ends of the control rods which interlock the drive and auger controls must be lubricated at least once a s

14SECTION 7: SERVICING YOUR SNOW THROWERWARNING: Before servicing, repairing, orinspecting, disengage all controls andstop engine. Wait until all mov

15• Drain the gasoline from the snow thrower, or place a piece of plastic film under the gas cap.• Tip the snow thrower up and forward so that it rest

16• Lightly tap the hex nut to dislodge the ball bearing from the right side of frame before removing the hex nut and bell washer from left end of sha

17NOTE: Fuel stabilizer is an acceptable alternative inminimizing the formation of fuel gum deposits duringstorage. Do not drain carburetor if using

18SECTION 9: PARTS LIST FOR MODELS 1028 & 11301111956177221127218Part of handle panel for reference only13254932420142611193029323438394041429114

19Models 1028 & 1130Ref. No.Part No. Part Description1. 684-0008A Shift Arm Assembly2. 747-0737† Chute Directional Control705-5204A* Chute Directi

2TABLE OF CONTENTSFINDING MODEL NUMBERThis Operator’s Manual is an important part of your new snow thrower. It will help you assemble, prepare and mai

201047443846193245174140129424339249203136492318485025163334351528262227211214111656371684228131630375151Model 1028

21Model 1028Ref. No.Part No. Part Description1. 714-0507 Cotter Pin2. 756-0178 Flat Idler 3. 784-5632B Auger Idler Arm4. 710-0347 Hex Cap Screw 3/8-16

2210434744384619324517920313649231848502516333435152826222721121411165637168422813163037521414039242942Model 1130

23Model 1130Ref. No.Part No. Part Description1. 714-0507 Cotter Pin2. 756-0178 Flat Idler 3. 784-5632B Auger Idler Arm4. 710-0347 Hex Cap Screw 3/8-16

24Models 1028 & 113012345674891011121314151618191916161620212223242526273233313028Supplied on engine29

25Models 1028 & 1130Ref. No.Part No. Part Description1. 710-0896 Hex Washer Screw 1/4-14 x.6252. 731-1324 Belt Cover3. 732-0710 Extension Spring4.

262519262724232221161718192029303132323234303227261925362124232212 2301018192021131114159376542403938Models 1028 & 11302883541333729

27Models 1028 & 1130Ref. No.Part No. Part Description1. 784-5648 Frame Cover2. 710-0896 Tap Screw 1/4-14 x.6253. 748-0190 Spacer.508 ID x.75 OD 4.

28Models 1028 & 1130126310127854913151417161920222220192821182118151314293132303032343738362335273911404142444551464748524653515455545016174937242

29Models 1028 & 1130Ref. No.Part No. Part Description1. 720-0223 Grip2. 710-0726 Tap Screw, 5/16-12 x.7503. 784-5642 Track Lockout Plate4. 710-015

3SECTION 1: IMPORTANT SAFE OPERATION PRACTICESThis sym bol points out im portant safety instructions, which if not follow ed, could endanger the pers

30NOTES

31MANUFACTURER’S LIMITED COMMERCIAL WARRANTY FOR:The limited warranty set forth below is given by Troy-Bilt LLC with respect to new merchandise used f

MANUFACTURER’S LIMITED WARRANTY FOR:The limited warranty set forth below is given by Troy-Bilt LLC with respect to new merchandise purchased and used

45. Never run an engine indoors or in a poorly ventilated area. Engine exhaust contains carbon monoxide, an odorless and deadly gas. 6. Do not operate

5SECTION 2: ASSEMBLING YOUR SNOW THROWERUnpacking• Remove screws from the top sides and ends of the shipping crate.• Set panel aside to avoid tire pu

6• If not already attached, slip the cables that run from the handle panel to the chute assembly into the cable guide located on top of the engine. Se

7The drive control also locks the auger control so youcan turn the chute directional control withoutinterrupting the snow throwing process. If the aug

8HeadlightThe headlight is on whenever the engine is running.Track Lock LeverThe track lock lever is located on the right side of the snow thrower and

9• Rotate choke knob to FULL choke position (cold engine start). If engine is warm, place choke in OFF position instead of FULL.• Push primer button t