TROY-BILT LLC, P.O. BOX 361131 CLEVELAND, OHIO 44136-0019Printed In USAOp e r a t O r ’s Ma n u a lSafe Operation Practices • Set-Up • Operation • Ma
Connecting the Battery CablesCALIFORNIA PROPOSITION 65 WARNING! Battery posts, terminals, and related accessories contain lead and lead compounds, che
Adjusting the Seat To adjust the position of the seat, pull up and hold the seat adjustment lever. Slide the seat forward or rearward to the desired p
described on the following pages.WARNING! Read and follow all safety rules and instr
Deck Lift Lever DECKHEIGHTLOHIchange the height of the cutting deck. To use, move
Fuel Level IndicatorThe Fuel Level Indicator is located on the left side of the tank.PTO /
TO AVOID SERIOUS INJURY OR DEATH• GO UP AND DOWN SLOPES, NOT ACROSS. • AVOID SUDDEN TURNS.• DO NOT OPERATE THE UNIT WHERE IT COULD SLIP OR TIP.• I
Driving The TractorWARNING! Avoid sudden starts, excessive speed and sudden stops. Lightly press the brake pedal to release the parking brake. Mov
Driving On Slopeswhere you may operate the tractor safely.WARNING! Do not mow on inclines
Engaging the PTOMove the throttle
MaintenanceWARNING! Before performing any maintenance or engine and remove key to prevent unintended s
Customer SupportPlease do NOT return the machine to the retailer or dealer without first contacting the Customer Support Department.If you have diffic
3. Remove the oil fill cap/ dipstick from the oil
Attach the hose coupler to the water port on your decks 3. Turn the water on.
Hex BoltAdjustment GearFigure 6-5AdjustmentsWARNING! Shut the engine off, remove the ignition key and engage the parking brake before
Front tire toe-in can be measured as follows:travel.In front of the axle, measure the dista
Cutting Deck RemovalTo remove the cutting deck, proceed as follows:position and engage the
the deck lift arm. See Fig. 7-3.7. Mo
Cutting BladesWARNING! Shut the engine off and remove ignition key before removing the cutting blade(s) for
BatteryCALIFORNIA PROPOSITION 65 WARNING: Battery posts, terminals, and related accessories contain lead and lead compounds, chemicals known to the St
Then route the belt around the two deck idler pulleys as 5. Remount the belt guards removed earlierRe-install the deck making sure
Problem Cause RemedyEngine fails to start 2. Spark plug wire(s) disconnected. 3. Throttle
Important Safe Operation Practices23General OperationRead, understand, and follow all instructions on the machine and in the manual(s) before attem
Component Part Number and Description
Component Part Number and Description
you purchased
Notes1133
FEDERAL and/or CALIFORNIA EMISSION CONTROL WARRANTY STATEMENTYOUR WARRANTY RIGHTS AND OBLIGATIONSMTD Consumer Group Inc, the United States Environment
GDOC-100223 Rev. AWARRANTED PARTS:The repair or replacement of any warranted part otherwise eligible for warranty coverage may be excluded from such w
MANUFACTURER’S LIMITED WARRANTY FORGDOC-100020 REV. AThe limited warranty set forth below is given by Troy-Bilt LLC with respect to new merchandise pu
4 se c t i O n 2 — iM p O r t a n t sa f e Op e r a t i O n pr a c t i c e sA missing or damaged discharge cover can cause blade contact or th
5se c t i O n 2 — iM p O r t a n t sa f e Op e r a t i O n pr a c t i c e sChildrenTragic accidents can occur if the operator is not alert to the
6 se c t i O n 2 — iM p O r t a n t sa f e Op e r a t i O n pr a c t i c e s3. complete stop wi
7se c t i O n 2 — iM p O r t a n t sa f e Op e r a t i O n pr a c t i c e sSafety SymbolsThis page depicts and describes safety symbols that may a
8 se c t i O n 2 — iM p O r t a n t sa f e Op e r a t i O n pr a c t i c e sSight and hold this level with a vertical tree...or a corner of a buil
Tractor Set-UpMoving The Tractor Manuallyrelief valve for occasions when it is necessary to
Comments to this Manuals