Operator’s ManualRear-tine Tiller Models634F — 634B —Bronco™ Super BroncoModel 634B ShownIMPORTANT: READ SAFETY RULES AND INSTRUCTIONS CAREFULLYWARNIN
SECTION 3: FEATURES AND CONTROLSA.WARNING: Before operating your machine, carefully read and understand all safety, controls and operating instruction
AA,WARNING: Before starting engine, be sure that both wheels are in WHEEL DRIVE position. See WhesI Drive Pins for instructions.Engaging the Forward
SECTION 4: OPERATIONA.WARNING: Before operating your machine, carefully read and understand all safety (Section 1), controls (Section 3) and operating
A WARNINGKEEP AWAY FROM ROTATING TINEG. ROTATING TINES WILL CAUSE INJURY.Stopping the Engine and Tiiler1. To stop the wheels and tines, release the Fo
TILLING TIPS & TECHNIQUESTilling DepthsAWARNING: Before tilling, contact your telephone or utilities company and inquire if underground equipment
TILLING TIPS & TECHNIQUES rCONT^Power CompostingPower composting simply means tilling under and burying in the soil all manner of organic matter s
TILLING TIPS & TECHNIQUES rCONT^Terrace Gardening (continued)• To create a terrace, start at the top of the slope and work down. Go back and forth
SECTION 5: MAINTENANCEA.WARNING: Before - : inspecting, cleaning or servicing themachine, shutoff engine, wait for all moving parts to come to a compl
*r?n>AWARNING: Before inspecting, cleaning or servicing the machine, shut off engine, wait for all moving parts to come to a complete stop, disconn
*r?n>AWARNING: Before inspecting, cleaning or servicing the machine, shut off engine, wait for all moving parts to come to a complete stop, disconn
TABLE OF CONTENTSContent PageCalling Customer Support...
AWARNING: Before inspecting, cleaning or servicing the machine, shut off engine, wait for all moving parts to come to a complete stop, disconnect spar
*r?n>AWARNING: Before inspecting, cleaning or servicing the machine, shut off engine, wait for all moving parts to come to a complete stop, disconn
*nn>AWARNING: Before inspecting, cleaning or servicing the machine, shut off engine, wait for all moving parts to come to a complete stop, disconne
SECTION 6: MODELS 630C, 634F & 634B PARTS LIST(A) For Model 630C(B) For Model 634F(C) For Model 634BREFNO.PART NO. DESCRIPTIONREFNO.PART NO.DESC
MODELS 630C, 634F & 634В24
MODELS 630C, 634F & 634BREFNO.PART NO. DESCRIPTION11916719 Cable Assembly, Reverse Clutch{B} (C)21916755Upper Handlebar3 1917479Bail, Forward Clut
MODELS 630C, 634F & 634В(A) For Mode! 630C(B) For Mode! 634F(C) For Model 634BREFN0.PART N0. DESCRIPTION1 GW-9517Snap Ring2 GW-1714 Bearing, Tape
MODELS 63QC, 634F & 634B(A) For Model 630C(B) For Model 634F(C) For Model 634BREFNO.PART NO. DESCRIPTION1 GW-9512Retainer, Snap Ring, “E” Type219
MODELS 630C, 634F & 634B13Inciuded with transmission when purchased as an assembiy only. Remove and discard when installing the transmissi
MODELS бЗОС, 634F & 634ВHold Tines With Blunt End Toward Yout Used on Left side of tiller ^ Used on Right side of tiller(A) For Model 630C
SECTION 1: SAFETYThis machine meets voluntary safety standard B71.8^1996, which is sponsored by the Outdoor Power Equipment Institute, Inc., and
MODELS 630C, 634F & 634В30
MODELS 630C, 634F & 634ВREFNO.PART NO. DESCRIPTION1 1107382 Flat Washer, 5/162 1108841Key,3/16“x1-1/2=(B (C)3 1916531 Pulley, Engine Drive (B) (C)
TROY-BILT TILLER LIFETIME LIMITED WARRANTYWHAT PRODUCT IS COVEREDAll Troy-Bilt branded rear tine walk-behind tillers with gear drive transmissions.Thi
4. Exercise caution to avoid siipping or falling.5. If the unit should start to vibrate abnormally, stop the engine, disconnect the spark plug wire
Decals,For your safety and the safety of others, various safety and operational decals are located on your unit (see Figure 1-2). L;Keep the de
SECTION 2: ASSEMBLYA.WARNING: To prevent personal injury or property damage, do not start the engine until all assembly steps are complete and you hav
Fig. 2.2: Attach hantllebar (S.SHPMoitelshown).2. Remove the hairpin cotter (L, Fig. 2-3) and wheel drive pin (M) from the wheei hub (0) and wheel sh
4. Thread the #10-24 hex nut (Z, Fig. 2-5)halfway onto the screw (V). : : : : :5. Thread the screw (V) into the cable adjuster (X). : ï: : ^6. Ho
bibKij: uHbuKLbVbLubThe transmission was filled with gear oil at the factory. However, you should check the gear oil level at this time to make certai
Comments to this Manuals