Operator’s ManualRear-tine Tiller Models 630C—Tuffy®634A—Super Bronco™ 634K—ProLineModel 634A ShownIMPORTANT: Read safety rules and instructions care
SECTION 3: FEATURES AND CONTROLSAWARNING: Before operating your machine, carefully read and understand all safety, controls and operating instructions
AAWARNING: Before starting engine, be sure that both wheels are in WHEEL DRIVE position. See Wheels Drive Pins for instructions.Engaging the Forward C
A WARNING: Before operating your machine, carefully read and understand all safety (Section 1), controls (Section 3) and operating instructions (Secti
ik WARNING&KEEP mm FROM ROTATING TINES. ROTftTIHG TIMES WILL CAUSE INJURY.Stopping the Engine and Tiller1. To stop the wheels and tines, release
TILLING TIPS & TECHNIQUESTilling DepthsA.WAKNiNG: Before tilling, contact your telephone or utilities company and inquire If underground equipment
TILLING TIPS & TECHNIQUES (CQNT)APower CompostingPower composting simply means tilling under and burying in the soil all manner of o
TILLING TIPS & TECHNIQUES (CQNT)Terrace Gardening (continued)• To create a terrace, start at the top of the slope and work down. Go
SECTIONS: MAINTENANCETILLER LUBRICATIONAWARNING: Before inspecting, cleaning or servicing the machine, shut off engine, wait for all moving parts to c
AWARNING: Before inspecting, cleaning or servicing the machine, shut off engine, wait for ail moving parts to come to a complete stop, disconnect spar
AWARNING: Before inspecting, cleaning or servicing the machine, shut off engine, wait for ail moving parts to come to a complete stop, disconnect spar
TABLE OF CONTENTSContent PageContent PageCustomer Support 2Maintenance 17Safety 3Off-season Storage 21Assembly 6Troubleshooting 22Features and Control
AWARNING: Before inspecting, cleaning or servicing the machine, shut off engine, wait for ail moving parts to come to a complete stop, disconnect spar
AWARNING: Before inspecting, cleaning or servicing the machine, shut off engine, wait for ail moving parts to come to a complete stop, disconnect spar
AWARNING: Before inspecting, cleaning or servicing the machine, shut off engine, wait for ail moving parts to come to a complete stop, disconnect spar
SECTION 6: MODELS 630C, 634A & 634K PARTS LIST1 ^(A) For Model 630C(B) For Model 634A and 634KREFNO.PART NO. DESCRIPTIONREFNO.PART NO. DESCRIPTION
MODELS 630C, 634A & 634K24
MODELS 63QC, 634A & 634KREFNO.PART NO. DESCRIPTION1 1916719 Cable Assembly, Reverse Clutch (B)2 1916755 Upper Flandlebar3 747-04210 Bail, Forward
MODELS 630C, 634A & 634K(A) For Model 630C(B) For Model 634A and 634KREFNO.PART NO. DESCRIPTION1 GW-9517 Snap Ring2 GW-9400 Drive Shaft Bearing Cu
MODELS 63QC, 634A & 634KFRONT(A) For Model 630C(B) For Model 634A and 634KREFNO.PART NO. DESCRIPTION1 GW-9512 Retainer, Snap Ring, “E” Type2 19099
MODELS 630C, 634A & 634K13Included with transmission when purchased as an assembly only. Remove and discard when installing the transmission on ti
MODELS 63QC, 634A & 634KHold Tines With Blunt End Toward YouFRONTREFNO.PART NO. DESCRIPTIONREFNO.PART NO. DESCRIPTION1 710-0514 Flex Hd. Screw, 3/
SECTION 1: SAFETYThis machine meets voiuntary safety standard B71.8-1996, which is sponsored by the Outdoor Power Equipment Institute, Inc., and is p
MODELS 630C, 634A & 634K2430
MODELS 63QC, 634A & 634KREFNO.PART NO. DESCRIPTIONREFNO.PART NO. DESCRIPTION1 736-0159 Flat Washer, 5/16 (B)23 710-0520 HexHd. Screw, 3/8-16x1-1/2
TROY-BILT TILLER LIFETIME LIMITED WARRANTYWHAT PRODUCT IS COVEREDAll Troy-Bilt branded rear tine walk-behind tillers with gear drive transmissions.Thi
4. Exercise caution to avoid slipping or falling.5. If the unit should start to vibrate abnormally, stop the engine, disconnect the spark plug wire
DecalsFor your safety and the safety of others, various safety and operational decals are located on your unit (see Figure 1-2).Keep t
SECTION 2: ASSEMBLYAWARNING: To prevent personal injury or property damage, do not start the engine until all assembly steps are complete and you have
Fig. 2-3: Wheei in FREEWHEEL positionSTEP 4: INSTALL FORWARD CLUTCH CABLE1. Carefully unwrap the forward clutch cable (cable without an att
4. Check for correct tension on the forward drive belt by taking two measurements of the cable spring, as follows:a. With the Forward
i>l tP 6: UHtuK IKANSMISSIUN OIL LEVELThe transmission was filled with gear oil at the factory. However, you should check the gear oi
Comments to this Manuals