Troy-bilt Polar Blast 10530 User Manual

PRINTED IN U.S.A.Operator’s ManualSnow Thrower Model10530—Polar BlastIMPORTANT: READ SAFETY RULES AND INSTRUCTIONS CAREFULLYWARNING: This unit is equ

10• Repeat Auger Control Test to verify proper adjustment has been achieved. Repeat the previous steps to provide more slack in the cable, in necessar

11• Thread the lock nut outward (down the coupler) three full turns to provide more slack in the cable and reattach the spring to the bracket.• Check

12WARNING: Maximum tire pressure underany circumstance is 30 psi. Equal tire pressureshould be maintained at all times. Excessivepressure (over 30 ps

13Discharge ChuteThe base of the discharge chute and the spirals on the chute crank should be lubricated at least every 25 hours of use. Apply the lub

14SECTION 7: SERVICING YOUR SNOW THROWERWARNING: Before servicing, repairing, orinspecting, disengage all clutch levers andstop engine. Wait until al

15Figure 18Auger Belt• Remove the cotter pin and washer from the ferrule in order to disconnect the auger idler rod from the brake bracket assembly. S

16• Secure the two halves with the two bolts and lock washers removed earlier. Refer to Figure 18.• Attach the “Z” fitting of the cable into the brake

17Off-season StorageWARNING: Never store engine with fuel intank indoors or in poorly ventilated areas,where fuel fumes may reach an open flame,spark

182429293020391324555768252540428183157254327131713914252634342632141421211610231213351137251322191333251441281536384445464714254952505354555651485859

19Model 10530Ref. No.Part No. Part Description1. 05244A Bearing Housing2. 618-0281A Bracket Assembly: Auger Break3. 684-0090A Impeller Assembly: 16”4.

2TABLE OF CONTENTSContent PageImportant Safe Operation Practices ... 3Loose Parts

20Model 1053018127617816911454966435353645451018182473324253923346714512775716458222129135652372223313291819474961481562275166423633347306511656471949

21Model 10530Ref. No.Part No. Part Description1. 05523 Pivot Support Bracket2. 750-1302A Spacer, .6725 x 1.125 x 2.4853. 618-0279 Dogg Assembly LH4. 6

22Model 1053011234545191919196677991021132911222431172723152621151425161822112015283015231321333232AAAA3334343535363738394042434481243

23Model 10530Ref. No.Part No. Part Description1. 646-0012 Cable Assembly: Auger/Drive2. 684-0053B Chute Crank Assembly, Lower3. 705-5266 Chute Crank B

24Model 10530Ref. No.Part No. Description1. 07386 Washer2. 684-0123A Belt Cover Bracket Assembly3. 710-0191 Hex Screw 3/8-24 x 1.25”4. 710-0237 Hex Sc

25Model 10530Ref. No.Part No. Description1. 710-0276 Carriage Screw2. 710-0458 Carriage Bolt 5/16-18 x 1.75”3. 710-0805 Hex Bolt 5/16-18 x 1.5”4. 710-

26Model 10530NOTE: When rebuilding a gearbox assembly, include 3 oz. of Shell Alvania EP Lead-Free Grease (Part No. 737-0168).Ref. No.Part No. Descrip

27D06575®D0657710.5 HPTOUCH 'N TURN STEERING • ALL WHEEL DRIVE • ELECTRIC START • JUST ONE HAND ® OPERATION D06574DANGERNEVER PUT HAND IN CHUTE.

MANUFACTURER’S LIMITED WARRANTY FOR:The limited warranty set forth below is given by Troy-Bilt LLC with respect to new merchandise purchased and used

3SECTION 1: IMPORTANT SAFE OPERATION PRACTICESThis symbol points out important safety instructions, which if not followed, could endanger the persona

44. Never operate with a missing or damaged discharge chute. Keep all safety devices in place and working.5. Never run an engine indoors or in a poorl

5SECTION 2: ASSEMBLING YOUR SNOW THROWERNOTE: All references to right or left side of the snowthrower are determined from behind the unit in theopera

6Attaching Chute Directional Control• Remove the hairpin clip from the upper rod and slide the upper rod through the bracket and into the lower rod. S

7Figure 7Shift Lever The shift lever is located in the center of the handle panel and is used to determine ground speed and direction of travel. It ca

8Wheel Steering ControlsThe left and right wheel steering controls are located on the underside of the handles and are used to assist in steering the

9NOTE: Always cover vent hole in primer button whenpushing. Additional priming may be necessary for firststart if temperature is below 15°F.• Grasp st