TROY-BILT LLC, P.O. BOX 361131 CLEVELAND, OHIO 44136-0019Printed In USAOperatOr’s ManualSafe Operation Practices • Set-Up • Operation • Maintenance •
10 sectiOn 3 — asseMbly & set-upAdjustmentsCutting HeightThe cutting height adjustment lever is located above the rear left wheel.Depress height a
Controls and Features411Blade ControlThe blade control is attached to the upper handle of the mower. Depress and squeeze it against the upper handle t
Operation512Figure 5-1Starting EngineWARNING: Be sure no one other than the operator is standing near the lawn mower while starting engine or operatin
Maintenance & Adjustments613MaintenanceGeneral RecommendationsAlways observe safety rules when performing any maintenance.The warranty on this law
14 sectiOn 6— Maintenance & adjustMentsEngine CareA list of key engine maintenance jobs required for good performance by the mower is given below.
15sectiOn 6 — Maintenance & adjustMentsRemove back cover of speed control housing by removing the three screws securing it to the housing. See Fig
Service7165. Lubricate the engine crankshaft and the inner surface of the blade adapter with light oil. Slide the blade adapter (and wave washer, if
17sectiOn 7 — serviceCarefully remove old battery and replace with new one. Connect the positive lead to the positive side of the battery pack, then c
18 sectiOn 7— serviceReplacing FuseThe electric starter circuit and battery are protected by a 40 ampere fuse. If the fuse burns out, the electric sta
Troubleshooting819Problem Cause RemedyEngine Fails to start Blade control disengaged.Spark plug boot disconnected.Fuel tank empty or stale fuel.Engine
Customer SupportPlease do NOT return the machine to the retailer or dealer without first contacting our Customer Support Department.If you have diffic
Troubleshooting820Problem Cause RemedyUneven cut Wheels not positioned correctly. Dull blade.1.2.Place all four wheels in same height position (if equ
Notes921
22Model Series J8302843424144114535121010232673937149513363131152152191783814462051485053422346184647271634253026299263040103332241025ABBA565455465758
23Ref No.Part Number Description1 746-04464 Drive Cable2 735-04059 Rubber Grommet3 687-02398 Drive Control4 732-04516 Shift Spring5 747-04879 Blade Co
24Model Series J83028331223253237381011213020181615142629272812954154238131734353122243639716194042
25Ref No.Part Number Description1 754-04176 V-Belt2 732-04338B Spring Lever3 720-04092 Foam Grip4 717-04540 Spur Gear, 14T - LH5 738-04278 Shldr. Scre
MANUFACTURER’S LIMITED WARRANTY FORGDOC-100020 REV. AThe limited warranty set forth below is given by Troy-Bilt LLC with respect to new merchandise pu
TROY-BILT LLC, P.O. BOX 361131 CLEVELAND, OHIO 44136-0019Impreso en Estados Unidos de AméricaManual del OperadOrMedidas importantes de seguridad • Con
Al propietario12Asistencia al ClientePor favor, NO devuelva la unidad al minorista o distribuidor sin ponerse en contacto primero con el Departamento
Medidas importantes de seguridad23ADVERTENCIA: La presencia de este símbolo indica que se trata de instrucciones importantes de seguridad que se deben
Important Safe Operation Practices23General OperationRead this operator’s manual carefully in its entirety before attempting to assemble this machine
4 sectiOn 2 — Medidas iMpOrtantes de seguridadNo ponga las manos o los pies cerca de las piezas rotatorias o en la tolva de la cortadora. El contacto
5sectiOn 2 — Medidas iMpOrtantes de seguridadMantenga a los niños fuera del área de trabajo y bajo estricta vigilancia de un adulto responsable además
6 sectiOn 2 — Medidas iMpOrtantes de seguridadADVERTENCIA: Su responsabilidad—Restrinja el uso de esta máquina motorizada a las personas que lean, com
7sectiOn 2 — Medidas iMpOrtantes de seguridadUse esta página como guía para determinar las inclinaciones de las pendientes en las que podría no tener
Montaje y Configuración38MontajeNOTA: Esta unidad se envía sin gasolina ni aceite en el motor. Llene con gasolina y aceite como se indica en las instr
9Sección 3 — Montaje y configuraciónEl centro de la bolsa se acopla desde el interior.Antes de acoplar el colector de césped, la tolva de abono debe e
10 Sección 3— Montaje y configuraciónAjustesAjuste de la altura de corteLa palanca de ajuste de altura de corte se ubica por encima de la rueda izquie
Controles Y Características411Control de CuchillaEl control de la cuchilla está unido a la manija superior. Presione la manija de control de la cuchil
Funcionamiento512Figura 5-1Encendido del MotorADVERTENCIA: Asegúrese que ninguna persona aparte del operador permanezca cerca de la podadora mientras
Mantenimiento Y Ajustes613MantenimientoRecomendaciones GeneralesRespete siempre las reglas de seguridad cuando realice tareas de mantenimiento.La gara
4 sectiOn 2 — iMpOrtant safe OperatiOn practicesA missing or damaged discharge cover can cause blade contact or thrown object injuries.Many injuries o
14 sección 6— ManteniMientO y ajustesAjustesCable de Velocidad VariableEl ajuste periódico del cable de velocidad variable puede ser necesario debido
15sección 6 — ManteniMientO y ajustesUsando un par de tenazas de nariz de aguja o instrumento similar, mueva el ojal en el cable sólo una ranura a la
Servicio716ADVERTENCIA: Si la cuchilla está desequilibrada generará vibraciones excesivas cuando rote a altas velocidades. Esto puede producir daños a
17sección 7 — serviciOAbra la cubierta de la batería, quite los conductores positivos y negativos de la batería, quite y reemplace por una nueva bater
18 sección 7— serviciOReemplazo del fusibleEl circuito del arrancador eléctrico y la batería están protegidos por un fusible de 40 amperes. Si el fusi
Solución de problemas819Problema Causa RemedioEl motor no arranca El control de lámina se retiró.Alambre de bujía desconectado.Depósito de combustible
20 sección 8 — sOlución de prObleMasProblema Causa RemedioDemasiada vibración Cuchilla floja o desequilibrada. Cuchilla abollada.1.2.Apriete la cuchil
Notas921
GARANTÍA LIMITADA DEL FABRICANTE PARAGDOC-100020 REV. ATroy-Bilt LLC, P.O. BOX 361131 CLEVELAND, OHIO 44136-0019, Teléfono: 1-866-840-6483, 1-330-558
5sectiOn 2 — iMpOrtant safe OperatiOn practicesServiceSafe Handling Of Gasoline:To avoid personal injury or property damage use extreme care in handli
6 sectiOn 2 — iMpOrtant safe OperatiOn practicesSpark ArrestorWARNING: This machine is equipped with an internal combustion engine and should not be u
7sectiOn 2 — iMpOrtant safe OperatiOn practicesSight and hold this level with a vertical tree...or a corner of a building...or a fence postFold along
Assembly & Set-Up38AssemblyNOTE: This unit is shipped without gasoline or oil in the engine. Fill up gasoline and oil as instructed in the accompa
9sectiOn 3 — asseMbly & set-upAttach center top of bag from inside of frame.Before attaching the grass catcher, the mulching baffle must be remove
Comments to this Manuals